HostingBlog
ProductCooling SystemsProfit RankingHostingBlogAbout UsMore
CartLeedMiner

Your cart is empty

Browse products or send a quote request when you are ready.

Browse miners
Home/Blog/Antminer Fan Status: Read RPM, Alerts and Support Records
Back to Blog

Antminer Fan Status: Read RPM, Alerts and Support Records

Mining GuideNovember 19, 20267 min read
November 19, 20267 minutes readUpdated November 19, 2026

Separate fan settings from measured RPM, preserve alert context and prepare a useful service handover.

By LeedMiner Editorial
XFacebookLinkedIn
LeedMiner guide to Antminer fan RPM, alerts and service records, with a real photograph of mining equipment.

Table Of Contents

1. Separate fan speed, control settings and machine state2. Read an alert with its channel and surrounding log3. Hand over a record that supports the next action

Share Article

XFacebookLinkedInPinterestWhatsAppTelegram

A fan reading is useful when it is attached to the right machine, firmware and operating state. Before treating a missing fan or unusual RPM value as a diagnosis, capture the complete status view and compare it with the log from the same interval. The useful result is a clear decision: continue a documented observation, stop under the site's operating procedure, or hand a specific fault record to qualified support.

This guide explains how to read and record Antminer fan status. It does not prescribe replacement parts, a universal RPM target or a repair sequence. The worksheet is LeedMiner's suggested operating record; the model-specific examples below come from BITMAIN documentation. The mining-site photographs illustrate equipment and operating environments, not a test of the machine you own.

1. Separate fan speed, control settings and machine state

BITMAIN's status-page reference defines the fan field as rotational speed in RPM and distinguishes chip temperature from PCB temperature. Its 19-series interface guide separately documents fan-status displays, fan-percentage settings and work/sleep modes. A control percentage and a measured speed therefore belong in different columns of your record.

Rows of air-cooled mining equipment in a mining facility, illustrating the machines whose fan readings need individual records.
Keep each status capture tied to one equipment record.

Start with the full model name, installed firmware version and a private asset identifier. Then record the capture time, time zone and whether the equipment was starting, working, sleeping or stopping. If the interface does not expose one of those states, write “not shown” rather than inferring it from the fan sound. Include the time since the last restart when available.

Record every displayed fan channel, retaining its label and unit. A screenshot cropped to a single red number may remove the machine identity or another relevant reading. Keep the original capture and make a separate sharing copy if account or network details are visible. A repeated screenshot should have a new timestamp, so two observations cannot be mistaken for simultaneous readings.

FieldWhat to recordWhat it does not establish by itself
Fan speedChannel label, displayed RPM and capture timeAirflow through every part of the machine
Fan settingAutomatic/manual state or percentage, if shownThe actual measured RPM of every fan
TemperatureThe full sensor label, value and unitThat an inlet, board and chip reading are interchangeable
Operating stateThe state actually reported by the interfaceNormal mining output merely because the page is reachable
HashrateThe named measurement window and local sourceThe pool's accepted work over a different interval

For comparisons, use a known working record from the same unit where possible. If comparing another machine, document the differences in model, firmware, operating mode and capture conditions. A convenient neighbor is not automatically a valid reference. Do not turn the highest RPM in a group into a target setting for the rest of the fleet.

If the question is whether mining output recovered, compare the appropriate intervals using our miner and pool hashrate guide. Fan readings provide equipment context; they do not replace accepted-work evidence.

2. Read an alert with its channel and surrounding log

BITMAIN's fan-problem reference describes a four-fan configuration whose FAN1–FAN4 interface labels correspond to controller connections. Use that mapping only for the documented configuration. It is not a statement that every air-cooled ASIC, hydro unit or modified machine has four monitored fans.

Mining machines arranged on facility racks, used as context for comparing individual fan channels and equipment status.
A channel label is more useful than a screenshot of an isolated number.

Save the exact alert wording and enough preceding and following log entries to preserve the sequence. Record whether it appeared immediately after startup, during an otherwise steady period, or following an operator action. Avoid translating an unfamiliar code into a fault name before checking the documentation for that model and firmware.

For example, BITMAIN's S19 XP log guide associates F:1 with fan abnormalities, P:1 with high-temperature protection, and J:6 with temperature-sensing trouble. Those examples help separate a fan event from other conditions in that documented family. They are not a universal code dictionary for newer firmware or another manufacturer's equipment.

Observed symptomUseful evidence to addDecision to avoid
One channel shows zero or disappearsFull channel list, operating state, timestamp and matching log intervalOrdering a replacement from the screenshot alone
One reading differs sharply from the othersThe same channel's earlier record and any associated alertApplying a universal percentage difference as a failure rule
All readings change togetherMode, settings and site events recorded at the same timeAssuming every fan independently failed
Fan alert and temperature alert appear togetherExact sensor labels and the order of the eventsDeciding which event caused the other without further evidence

These are questions for an incident record, not automatic diagnostic rules. Mark each field as observed, reported by another person or still unknown. That distinction lets support request the missing evidence without treating an assumption as a measurement.

Do not bypass fan monitoring, disable protection or keep restarting an unsafe machine to obtain a cleaner screenshot. Physical inspection and any component work belong to the site's isolation procedure and the appropriate qualified service personnel. Preserve what can be captured safely; a complete log is not more important than stopping an unsafe operating condition.

3. Hand over a record that supports the next action

A useful handover connects the original symptom, the equipment identity and the decision still required. Separate “fan alert observed” from “component fault confirmed” and “repair verified.” Each is a different stage, and a case should not advance simply because someone refreshed the dashboard.

Technicians working with mining equipment and cabling inside a mining facility, illustrating a service handover environment.
Keep service actions and their verification attached to the same case.

Use a short handover note with the asset identifier, exact model and firmware, first-observed time, affected channels, log interval and actions already taken. List the original and current settings where a change was authorized. If nothing was changed, say so. Keep a named owner and a specific next question, such as whether support needs another log interval or an isolated physical inspection.

Share records through the agreed private support channel. Our log export and redaction checklist explains how to preserve diagnostic context while removing unnecessary account and network identifiers. Do not include passwords or wallet secrets in the case. A public discussion copy and a manufacturer support package may need different levels of detail.

For equipment identification, the Antminer S21 XP catalog page is an example of an exact product reference. Its listing does not identify your individual unit or make the S19 XP fault-code examples applicable to it. Confirm the model on the equipment and use the documentation that matches that model.

Antminer S21 XP 270 TH/s

Approved catalog photograph of the air-cooled Antminer S21 XP, used as a model-identification reference.
Antminer S21 XP — catalog photograph.

Air-cooled Bitcoin miner. Confirm your unit’s model before using a fault-code reference or service documentation.

View current product details

After an approved service action, retain the original record and add a new one. Capture the same fields, identify the action and state the actual observation period. Check whether the original symptom recurred and whether relevant alerts remain. If the machine is intended to mine, record fresh worker activity separately. Do not invent a universal number of minutes that proves every repair is complete.

Close the case only against the agreed acceptance conditions. If the alert remains unexplained, label the case unresolved and carry forward the missing evidence. If it disappears, state what was actually verified and over what interval. This makes the record useful when a later operator sees the same symptom again.

Need help preparing an equipment or service inquiry? Contact LeedMiner with the model, firmware and a concise symptom summary. For hosted equipment, establish who can capture the local status and who owns the next service action before requesting additional screenshots.

Related Posts

ASIC delivery damage: evidence before powerNovember 16, 2026ASIC Miner Delivery Damage: What to Record Before Power-On

Document carton damage, preserve packing materials and prepare a clear support record before installing an ASIC miner. I

Litecoin and Dogecoin merged mining editorial cover featuring the approved Antminer L9 catalog photographSeptember 26, 2026Why Litecoin Is Rising—and What LTC Miners Should Watch

An LTC price rally does not tell the whole Scrypt mining story. Compare Litecoin and Dogecoin revenue together, and dedu

BCH rally editorial cover featuring the approved Antminer S21 XP catalog photographSeptember 26, 2026Why BCH Rallied—and What It Means for Bitcoin Cash Miners

CME’s planned BCH futures provide a concrete news backdrop to the rally. Here is how to separate the price story from ac

Need Help?

Loading security check…

Leedminer offers competitive miner prices, accelerating your Return on Investment (ROI).

+86 133 5291 7253info@leedminer.com

Information

  • Shop
  • My Account
  • Miners' Profitability
  • Coin List
  • Halving Countdown
  • Blog

Support

  • Contact Us
  • FAQs
  • Payment Methods
  • Return & Warranty
  • Terms & Conditions
  • Privacy Policy

Company

  • About Us
  • Our Team
  • Exhibitions
  • Partners
  • Fraud Prevention
LEEDMINER

© 2017-2026 LeedMiner All rights reserved. Storefront locale English · leedminer.com

We use cookies to improve your experience.

Cookie Settings

We use essential cookies for cart and account sessions. Optional analytics and marketing scripts only load after consent.

Privacy Policy