Beschreibung

Play video
The First Choice for Home Mining

The C2 is an immersion liquid cooled mining kit designed for home and office users.
The C2 kit accommodates two ASIC miners andis the most cost-effective distributed immersion liquid cooling solution available! 


11

More Quiet & Energy saving Intelligent Speed Adjustment With EC Fan

The C2 dry cooler supports automatic frequency adjustment according to the temperature

change of the coolant. It can respond to changes in ambient temperature in real-time,

ensuring operation with the lowest power consumption.

15 Minutes to Install

1 1
2 1
3 2
4
5

Multi-mode switching&Supports heat recovery

C2 supports the return of mining waste heat to heating systems, including swimming
pools, underfloor heating, etc.

C2 TANK
Technical Specifications

Outer Size 455(L)*508(W)*536(H)mm
17.91(L)*20(W)*21.1(H)in
Inner Size 398(L)*298(W)*392(H)mm
15.67(L)*11.73(W)*15.43(H)in
G.W 40.6kg
Coolant Volume 80L
Input Voltage Single-phase 200-240V
50/60Hz
Strom 180W(220V 50Hz)
Display 1.32”OLED Screen
Noise 45dB(A)
Inlet/Outlet Temp 45/60℃

C2 Dry Cooler Technical Specifications

Größe 1076(L)*285(W)*531(H)mm
42.36(L)*11.22(W)*20.9(H)in
Strom 5-400W(220V 50Hz)
Input Voltage Single-phase 200-240V 50/60Hz
G.W 43.3kg
Intelligent Speed Tuning Automatically adjust the speedaccording to the temperature
Cooling Capacity 12kW@35℃12kW@95℉
Noise 68dB(A) 10m
EC Fan 2 pcs

Accessories
Product specification

Pipeline 5m*2
Fan Simulator 4 pcs
Oil Filling Pump 1 set
Miner Handle 4 pcs(Antminer)
Gasket 8 pcs
User Manual 1 pcs
12V Power Adapter 1 pcs
Sticker 1 pcs

FAQ

Electrical questions

What is the connection method of the C2 power supply?

The mining rigs in C2 is directly connected to the power supply or PDU at home, and the tank and dry cooler are connected through standard C13 connectors.

What is the operating logic of the C2 fan? Can it be adjusted automatically?

Our C2 uses an EC fan to adjust the speed according to the temperature of the oil entering the tank (dry cooler oil temperature).There are 2 modes to choose (the mode is changed by a button inside the waterproof junction box outside the dry cooler).Press the button down is HEATING mode (waste heat utilization mode) 41.3℃ to start the dry cooler, 49.7℃ to maximize the dry cooler speed. Press the button up is NORMAL mode (normal operation mode), 20.5℃ to start the dry cooler, 28.9℃ to maximize the dry cooler speed.

How long is the pipeline for the C2 tank?

We provide two 5m pipeline as standard, and we also support customizing other lengths for a fee.

Will the tank automatically power on after a power outage?

Following a power outage, the tank is unable to initiate an automatic startup and necessitates manual activation by clicking on the screen.

Parameter questions

How noisy is the C2 system?

The C2 tank noise about 45dB, the dry cooler will reach 68dB(A) 10m at full speed.

What is the size of the C2 pump?

With an input voltage of 220V 50Hz, the pump has a power of 150W, and the maximum flow rate for circulating the Coolant is 36L/min, with a maximum head of 10m.

What is the C2 pipeline connector size?

C2 pipeline connector size is DN25 (External thread diameter Pipeline diameter 32mm).

After-sales questions

What should you do if there is high-frequency noise in the junction box when the fan is running at full speed?

In general, this issue might arise due to the loose fastening of screws on the internal PCB board of the junction box. You should dismantle the junction box and tighten the screws securely. If the screws cannot be tightened, you can try to replace the screws or add gaskets to tighten the screws (M3 screws and gaskets). If the problem persists, you can try to add gaskets (preferably rubber anti-vibration pads) at the bottom of the dry cooler to raise the fan to prevent noise caused by contact between the bottom of the dry cooler and the ground.

How to properly unload oil to avoid waste?

First, pump the oil out using the oil filling pump in the accessories. At the same time, there is an oil discharge port in the middle of the liquid separator plate at the bottom of the tank. After removing the screw, plug the oil filling pump in to clean up the liquid at the bottom of the liquid separator plate.

How does the oil filling pump work in accessories?

Instructions1. Connect the pump to the inlet and outlet pipes: Ensure a tight seal between the pipes and the pump to prevent low pressure or leakage. The arrow on the pump head indicates the direction of the outlet.2. Put the water inlet pipe below the coolant level, and put the water outlet pipe in the corresponding storage coolant receptacle.3. Connect the pump to the pump power adapter and then power on.

What is the material of C2 kit?

The material of C2 tank is cold-rolled steel , the dry cooler is copper and aluminum fins.

If the C2 pump stops or reports an error, what will happen?

If the pump stops working, a “Pump Error” prompt will appear on our Tank’s display screen, accompanied by an alarm sound. If this situation is not addressed, the temperature of the coolant will continue to rise due to the inability to dissipate heat. Eventually, this will trigger the temperature protection mechanism of the mining rigs, causing them to stop operating automatically.

Note

About the transportation of liquid cooling equipment

For most areas, the liquid cooling equipment will be shipped to you via sea freight. Ports and receiving points in different regions will incur different shipping charges. It is recommended that you contact customer service to confirm address details and calculate shipping costs before placing an order.

Advisory Service

Please send us your RFQ to get your exclusive sales manager assistance.

请在浏览器中启用JavaScript来完成此表单。

加载

1-algorithm

Hashrate

3-consumption

Strom

2-hashrate

Efficiency

Minable pools for Immersion Cooling C2

未找到相关矿池数据

Immersion Cooling C2

Minable coins:

C2
$630.00 - $2108.00
C2 Tank C2 Tank + Dry cooler C2 Tank + Dry cooler + Coolant

Please confirm the current inventory and pricing with customer service before placing your order, as prices may fluctuate.

SECURE
Lifetime Customer Support
Direct Supplies Price
Fast shipping
Manufacturers Warranty
Bundle Discounts
PSU Included

Profitability

Week Month 3 Months Year
未找到算力或算法数据。请确保已在产品元数据中设置它们。

Description​

Play video
The First Choice for Home Mining

The C2 is an immersion liquid cooled mining kit designed for home and office users.
The C2 kit accommodates two ASIC miners andis the most cost-effective distributed immersion liquid cooling solution available! 


11

More Quiet & Energy saving Intelligent Speed Adjustment With EC Fan

The C2 dry cooler supports automatic frequency adjustment according to the temperature

change of the coolant. It can respond to changes in ambient temperature in real-time,

ensuring operation with the lowest power consumption.

15 Minutes to Install

1 1
2 1
3 2
4
5

Multi-mode switching&Supports heat recovery

C2 supports the return of mining waste heat to heating systems, including swimming
pools, underfloor heating, etc.

C2 TANK
Technical Specifications

Outer Size 455(L)*508(W)*536(H)mm
17.91(L)*20(W)*21.1(H)in
Inner Size 398(L)*298(W)*392(H)mm
15.67(L)*11.73(W)*15.43(H)in
G.W 40.6kg
Coolant Volume 80L
Input Voltage Single-phase 200-240V
50/60Hz
Strom 180W(220V 50Hz)
Display 1.32”OLED Screen
Noise 45dB(A)
Inlet/Outlet Temp 45/60℃

C2 Dry Cooler Technical Specifications

Größe 1076(L)*285(W)*531(H)mm
42.36(L)*11.22(W)*20.9(H)in
Strom 5-400W(220V 50Hz)
Input Voltage Single-phase 200-240V 50/60Hz
G.W 43.3kg
Intelligent Speed Tuning Automatically adjust the speedaccording to the temperature
Cooling Capacity 12kW@35℃12kW@95℉
Noise 68dB(A) 10m
EC Fan 2 pcs

Accessories
Product specification

Pipeline 5m*2
Fan Simulator 4 pcs
Oil Filling Pump 1 set
Miner Handle 4 pcs(Antminer)
Gasket 8 pcs
User Manual 1 pcs
12V Power Adapter 1 pcs
Sticker 1 pcs

FAQ

Electrical questions

What is the connection method of the C2 power supply?

The mining rigs in C2 is directly connected to the power supply or PDU at home, and the tank and dry cooler are connected through standard C13 connectors.

What is the operating logic of the C2 fan? Can it be adjusted automatically?

Our C2 uses an EC fan to adjust the speed according to the temperature of the oil entering the tank (dry cooler oil temperature).There are 2 modes to choose (the mode is changed by a button inside the waterproof junction box outside the dry cooler).Press the button down is HEATING mode (waste heat utilization mode) 41.3℃ to start the dry cooler, 49.7℃ to maximize the dry cooler speed. Press the button up is NORMAL mode (normal operation mode), 20.5℃ to start the dry cooler, 28.9℃ to maximize the dry cooler speed.

How long is the pipeline for the C2 tank?

We provide two 5m pipeline as standard, and we also support customizing other lengths for a fee.

Will the tank automatically power on after a power outage?

Following a power outage, the tank is unable to initiate an automatic startup and necessitates manual activation by clicking on the screen.

Parameter questions

How noisy is the C2 system?

The C2 tank noise about 45dB, the dry cooler will reach 68dB(A) 10m at full speed.

What is the size of the C2 pump?

With an input voltage of 220V 50Hz, the pump has a power of 150W, and the maximum flow rate for circulating the Coolant is 36L/min, with a maximum head of 10m.

What is the C2 pipeline connector size?

C2 pipeline connector size is DN25 (External thread diameter Pipeline diameter 32mm).

After-sales questions

What should you do if there is high-frequency noise in the junction box when the fan is running at full speed?

In general, this issue might arise due to the loose fastening of screws on the internal PCB board of the junction box. You should dismantle the junction box and tighten the screws securely. If the screws cannot be tightened, you can try to replace the screws or add gaskets to tighten the screws (M3 screws and gaskets). If the problem persists, you can try to add gaskets (preferably rubber anti-vibration pads) at the bottom of the dry cooler to raise the fan to prevent noise caused by contact between the bottom of the dry cooler and the ground.

How to properly unload oil to avoid waste?

First, pump the oil out using the oil filling pump in the accessories. At the same time, there is an oil discharge port in the middle of the liquid separator plate at the bottom of the tank. After removing the screw, plug the oil filling pump in to clean up the liquid at the bottom of the liquid separator plate.

How does the oil filling pump work in accessories?

Instructions1. Connect the pump to the inlet and outlet pipes: Ensure a tight seal between the pipes and the pump to prevent low pressure or leakage. The arrow on the pump head indicates the direction of the outlet.2. Put the water inlet pipe below the coolant level, and put the water outlet pipe in the corresponding storage coolant receptacle.3. Connect the pump to the pump power adapter and then power on.

What is the material of C2 kit?

The material of C2 tank is cold-rolled steel , the dry cooler is copper and aluminum fins.

If the C2 pump stops or reports an error, what will happen?

If the pump stops working, a “Pump Error” prompt will appear on our Tank’s display screen, accompanied by an alarm sound. If this situation is not addressed, the temperature of the coolant will continue to rise due to the inability to dissipate heat. Eventually, this will trigger the temperature protection mechanism of the mining rigs, causing them to stop operating automatically.

Note

About the transportation of liquid cooling equipment

For most areas, the liquid cooling equipment will be shipped to you via sea freight. Ports and receiving points in different regions will incur different shipping charges. It is recommended that you contact customer service to confirm address details and calculate shipping costs before placing an order.

Advisory Service

Please send us your RFQ to get your exclusive sales manager assistance.

请在浏览器中启用JavaScript来完成此表单。

加载

Immersion Cooling C2 operates using the algorithm, capable of achieving a maximum hash rate of with a power consumption of just . It is recognized for its impressive energy efficiency of . Additionally, it features a noise level of .

Immersion Cooling C2 is a modern miner for , optimized for the algorithm. Manufactured by , it weighs and has dimensions of . The cooling mode utilized is Cooling, ensuring efficient thermal management. The miner interfaces through , making it user-friendly and adaptable for various setups.

The atmospheric temperature for optimal performance is .

Compare Immersion Cooling C2 With Similar Miners

Modell Coin Hashrate Strom Efficiency Earning 24H Daily Electricity Cost ShutDown Price Miner Price PayBack
(Days)
Net Profit
Per Day
Aethir Edge ATH Miner
Delivery Time: In-stock
Top Coin
100 ATH
18 W
N/A
$8.00
-$-0.02
$ $1,399
13.99 $/ATH
175
$7.98

Terms

All orders are dispatched in batches, with machines shipped within 3-7 days from stock; bulk orders may require an additional day or two. We aim to ship promptly via DHL Express, UPS, Fedex, or TNT after confirming full payment (wire transfers may take 3-7 business days, while cryptocurrency payments are usually verified within a few hours to 1 business day).

International shipping generally takes 5-8 business days, and DDP shipping can take 8-10 days.

*Please note that all sales are final and non-refundable.

All orders are dispatched in batches, with machines shipped within 3-7 days from stock; bulk orders may require an additional day or two. We aim to ship promptly via DHL Express, UPS, Fedex, or TNT after confirming full payment (wire transfers may take 3-7 business days, while cryptocurrency payments are usually verified within a few hours to 1 business day).

International shipping generally takes 5-8 business days, and DDP shipping can take 8-10 days.

*Please note that all sales are final and non-refundable.

Akzeptierte Zahlungsarten:
1. Banküberweisung/Wire Transfer (T/T)
2. USDT
3. Für andere Methoden wenden Sie sich bitte an unseren Vertriebsexperten.

*Alle Maschinenpreise schwanken auf der Grundlage des Kryptomarktes, daher sind unsere Angebote nur am Tag der Veröffentlichung gültig.

We primarily ship via DHL Express, UPS, or FedEx. For certain countries, we offer DDP (Delivery Duty Paid) shipping, meaning clients do not incur any duties or customs charges.

DDP Shipping Countries: United States, Germany, Russia, Dubai, United Kingdom, France, Belgium, Luxembourg, Netherlands, Denmark, Czech Republic, Poland, Austria, Ireland, Portugal, Sweden, Spain, Vietnam, Thailand, Malaysia, as well as Indonesia, the Philippines, Canada, and the entire European Union (note: some countries require a minimum order of 30kg).

To request DDP shipping, please contact us at [email protected]

For non-DDP countries or standard shipping, we can help reduce your tax by issuing a lower invoice.

*Our products exclude all value-added taxes and customs duties, and you will be responsible for paying any applicable taxes and duties according to your country’s laws. Additionally, if any miner needs to be returned to Hong Kong, the client will cover the extra shipping costs.

Wir bieten:
1. Marketing-Fotos und Video-Paket
2. Wettbewerbsfähige Großhandelspreise
3. Dropshipping-Service unterstützen
4. Technische Unterstützung

Frequently asked questions

How much does Immersion Cooling C2 make ?

As of Feb 09, 2025, considering an electricity cost of $0.04/KWh, the Immersion Cooling C2 has the following profit calculations:

  • Daily Net Profit: $0
  • Monthly Net Profit: $0
  • Yearly Net Profit: $0

1. Keep in a Protective and Ventilated Area

Select the case’s appropriate size, preferred colour, and preferred style to go with the decor of your space. Keep your Immersion Cooling C2 on a protective frame, open all sides for adequate airflow and install fans for more ventilation. Ventilation is the most important thing for mining hardware to deliver better. To create a well-ventilated inside and out, install fans as per requirement and use foaming or wooden frames.

2. Connect it to the Power Supply and Internet Connection

You must now connect your mining equipment to an electricity source. We are all aware that the primary need for cryptocurrency miners is energy. It is when you connect your miner to the power source that your miner gets the power to initiate. Connect your Immersion Cooling C2 to the internet connection, is interface for Immersion Cooling C2. Ensure it is connected to the internet.

3. Get an IP Address and Authorize Your Immersion Cooling C2

There are two ways to get an IP address: you can choose any of the two options at your convenience. The first option is the DHCP address by logging into the home router and filling in all the details. The other option is to install some free mining software and grab the IP address from there. Once done, paste the IP address on a new webpage and enter the credentials, such as your username and password, to authorize it.

4. Join and Set Up a Mining Pool

Entering a pool will improve your chances of receiving payments more frequently and consistently by rewarding you with small amounts of coin whenever all pool members complete an algorithm. A pool is a collection of cryptocurrency miners who cooperate and pool their hashing capacity to solve equations across the network. Once you have joined the pool, set it up per your mining requirements.

5. Set Up a Wallet

Multiple wallets, such as software or hardware wallets, are available online. Follow all the instructions on the official website of the crypto exchange or crypto wallet you choose. Then, you can use your wallet address as a method of payment to accept coins.

6. Configure Your Immersion Cooling C2

The next step is to set up your miner by filling in all the essential details in the interface that appears when you log in using the credentials provided. Fill in the details such as owner’s accounts, mining pool details, addresses, wallet addresses and other required fields.

7. Start Mining

Now that your Immersion Cooling C2 setup process is complete, you can start mining coins. Just be sure to launch the miner with a greater hash rate. Your Immersion Cooling C2 is now set up and running, and you can anticipate seeing a return on your investments.

8. Determine Profits and Assess Miner’s Activity

Now that your setup is complete and you have started mining , it’s crucial to analyze how well it performs compared to your expenses and keep a keen eye on the working of your Immersion Cooling C2.

RELATED PRODUCTS

Immersion Cooling Suite B24

$10300.00 - $112450.00

Immersion Cooling Suite M20

$4300.00 - $17140.00

Immersion Cooling B24 Dry cooler

$10419.00

Immersion Cooling C6

$1100.00 - $4349.00

COMPANY partnerS

You’re in good company, Supported by the world’s best.

Social Partners

Wir freuen uns, unsere Partnerschaft mit Rabidming Trades ankündigen zu können! Diese Zusammenarbeit wird Ihnen die neuesten Innovationen im Bereich des Krypto-Minings bringen und Sie mit der besten Ausrüstung und Expertenwissen versorgen, um der Zeit voraus zu sein.

Geek Of All Trades ist Ihre erste Anlaufstelle für Krypto-Mining-Fachwissen. Auf ihrem YouTube-Kanal finden Sie ausführliche Videos über ASIC-, GPU- und FPGA-Mining und können sich das Wissen aneignen, das Sie brauchen, um erfolgreich zu sein.

coingabbar x leedminer

CoinGabbar ist eine Plattform für Kryptowährungen, die eine Reihe von Funktionen und Dienstleistungen anbietet, wie z.B. Preisverfolgung und Marktanalysetools.

Die Plattform verfügt über Nachrichten- und Blogbereiche mit Artikeln über die neuesten Informationen und Entwicklungen aus der Welt der Kryptowährungen.

Coinpaper ist ein sich schnell entwickelndes Online-Magazin, das sich auf Themen wie Kryptowährungen und Blockchain-Technologie konzentriert.

Die Plattform bietet themenbezogene Nachrichten, Berichte, Analysen, Leitfäden und andere relevante Ressourcen für Einsteiger und erfahrene Krypto-Nutzer.

Start Mining with LeedMiner

Bitte aktiviere JavaScript in deinem Browser, um dieses Formular fertigzustellen.